On Orders Of $200
Designed to be used in conjunction with our Ultimate Reduced-Power Buffer/Hammer Spring, and Trigger Guard C-Clip.
*Taran Tactical recommends that you go to a certified gunsmith or Glock armorer for installation*
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Showing reviews 1-10 of 17 | Next
Noticeable Trigger Pull Reduction
Posted by JRemy on Aug 27th 2019
Installation was no issue and did it within 5 minutes of finally being able to sit down and accomplish the task. Installed put the gun back together to test fire the gun and make sure it worked properly in a dry fire. There was a noticeable reduction in trigger pull.
I bought this in addition to the reduce hammer spring as I took my shotgun out for some trap shooting and noticed it struggled with the light loads. With the combination of the two, it seemed to dramatically reduce the action pull back as well. I go back out next week for some fun and will see how well everything holds up then.
reduced versa max trigger pull to 5.5 lbs from 8.25 lbs
Posted by trdjohn on Aug 25th 2019
Installation was super easy on Rem Versa Max Synthetic. Only installed the trigger reset spring, lessened the pull to 5.5 lbs from 8.25 lbs. This is a bird gun and occasional skeet gun, so it brought it to acceptable level. Worked fine with 1145 fps Federal and Winchester target loads, no issues with trigger reset on doubles. After early dove season I'll replace the hammer spring and see how much it lowers it from 5.5 lbs
Posted by firstname.lastname@example.org on Aug 15th 2019
So this is the missing link it turns out. If you want your benelli m4 to run silky smooth and ultra fast. Replace this spring as well as the trigger spring. It makes a World of difference.
Modest reduction in trigger pull.
Posted by James King on Jul 17th 2019
Trigger plus hammer spring reduced trigger pull from 6.5 pounds to 4.5 pounds. As expensive as the springs and shipping were I had anticipated a trigger pull in the 3-4 pound range. Obviously my expectations were higher than reality.
Posted by Unknown on May 8th 2019
The Benelli M4 trigger is about 2 pounds lighter with this spring.
Works great in Remington versa max
Posted by Unknown on Aug 24th 2018
Easy to fix hard versa max trigger
Posted by Drundel on Feb 12th 2018
Good upgrade for the SBE1/2 for hunting. I put these in my SBE2 for hunting and I am already shooting better. I have a Shotkam on my gun and can see me pulling the gun to the left on days when I am wearing a heavy jacket.
There are some good videos in YouTube showing how to install.
Reduced Stock trigger pull by 3#
Posted by Matt on Nov 14th 2017
My original trigger pull on a stock Benelli M4 was average 9 5/8 # using 5 measurements on a timmney trigger weight gauge. I knew it was a tough pull, but dang! So I installed just the trigger spring since I need a set of retaining ring pliers to install the hammer spring. I used a set of tweezers and a small punch to do the install. It was easy. This was my first experience installing anything on a gun. After the install I was reading an average of 6 1/4 pound. I will install the hammer spring when the pliers come in.
Huge reduction in trigger pull force
Posted by Unknown on Oct 12th 2017
Installed both.....Reduced-Power Hammer Spring and Trigger Spring in a Versa Max.
Using a Wheeler Engineering Trigger Pull Scale.......
Stock springs - 7.6 - 8.0 lb.
TTI Springs - 3.5 - 3.8 lb.
Instantly made me a better shooter.
No misfires using Fiocchi low recoil slugs.
An absolute must have.
Smooth as a baby's bottom
Posted by Aaron on Apr 10th 2017
Excellent services by TTI staff getting my product out to me so quickly! So far, post test with Lyman Digital Trigger pull showed a WHOOPING 4 lbs and 8 oz from stock pre test of 6 lb 15 oz on my Stoeger M3K! Look forward for smooth transition from targets to targets. Thanks TTI!!
Showing reviews 1-10 of 17 | Next